Skip to content
OCCUPATIONAL TRAINING AND SUPPLY
CALL US: 1-630-655-3900
Occupational Training & Supply Inc.
Search our store.
Meet Our Team
Site Help / FAQ
Terms & Conditions
Air & Surface Sampling
Lead Based Paint Removers
Lead Dust Cleaners
Pipe Wrap & Lockdowns
Blackline Safety Products
Polyethelene (Poly) Sheeting
Silica Dust Tools and Equipment
Electrical & Jobsite Lighting
Fall Protection & Confined Space
Harness & Lanyard Combo
Self-Retracting Lifelines & Tripods
Global Harmonized System (GHS)
Health Care PPE
Indoor Air Quality
Austin Air Systems
Austin Air Machines
Austin Air Replacement Filters
Mold & Odor: Biological Cleaning
Mold Resistant & Fungicidal Coatings
Mold, Smoke & Odor
Negative Air Machines
Personal Protective Equipment
Hi-Vis Work Wear
Cold/Heat Stress & First Aid
Cartridges & Filters
Disposable Dust Masks
Spray Foam Insulation
Tapes & Adhesives
Nav Menu 6
Nav Menu 7
Nav Menu 8
Indoor Air Quality
Fiberlock® IAQ™ 6000 ZERO
IAQ 6000 GEN3
Zero VOC Mold Resistant* Coating – White
Professionals looking for a product with the highest possible mold resistant rating should look no further. IAQ 6000 GEN3 is uniquely formulated to resist mold growth on the dry coating surface, recommended for use on a multitude of surfaces and on new structural materials during building construction.
*Resists mold on the dry coating surface only
How to Use
Surfaces to be coated must be free of dust, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap and other surface contamination. Clean mold stained surfaces with IAQ Advanced Peroxide Cleaner, or use an EPA registered antimicrobial disinfectant cleaner such as IAQ 2000, IAQ 2500, ShockWave or ShockWave RTU. Patch irregularities with vinyl patching paste or an appropriate patching compound. IAQ 6000 GEN3 is self-priming over bare sheetrock, composition board, ceiling tile and concrete.
WALLBOARD, SHEETROCK, GYPSUM BOARD
Joint cement should be sanded smooth, but avoid abrading the paper.
Clean, then prime with IAQ 4000 rust inhibiting direct-to-metal primer.
Seal knots and stains with IAQ 5000 stain blocking primer.
Apply one coat of IAQ 3000 block filler if a denser surface is desired.
Apply IAQ 6000 GEN3 with a brush, roller or airless spray equipment.
Brush: Synthetic, nylon or polyester bristle
Roller: Synthetic fiber 3/8” nap or longer
Spray Settings: Pressure: 2000-3000 P.S.I. Tips: .019 to .021 tips
IAQ 6000 GEN3 may be tinted to any off-white or pastel based color. Add up to 2 oz. of universal colorant per gallon. Start with 50% of the tinting formula and adjust as necessary.
IAQ 6000 GEN3 is supplied ready to use, but can be thinned sparingly with water (up to 1/2 pint water per gallon) for proper application consistency if necessary. Apply IAQ 6000 GEN3 generously and uniformly by brush, roller, or airless spray. Apply one coat of IAQ 6000 GEN3 and ensure that the finished surface is properly sealed. To ensure that the finished surface is properly sealed, two-coats may be required on some porous surfaces.
Smooth Surfaces- 250-400 sq. ft. per gallon
Porous Surfaces- 150-300 sq. ft. per gallon
Clean tools and drippings with warm soapy water before IAQ 6000 GEN3 dries. Dispose of waste according to all existing local, state and federal regulations.
Store in a dry place at temperatures between 40°F (4.5°C) and 90°F. (32°C). Stir thoroughly. Do not mix with any other coatings, solvents or colors in oil. The IAQ 6000 GEN3 coating is resistant to mold only on the surface of the coating. No mold resistance claim is made other than to the coating itself. The use of this product does not protect users or others against food-borne or disease-causing bacteria, viruses, germs or other disease-causing organisms. Do not apply when air or surface temperature is below 50°F (10°C), or when drying conditions are poor or when surfaces are above a 15% moisture level content. Use adequate ventilation during application. When applying with a sprayer, wear a NIOSH approved respirator with any R, P, N or HE filter. For interior use only.
100% acrylic, water-based coating
White, tintable and durable
VOC Compliant: All US and Canada
Tested by independent laboratories for mold resistance: ASTMG-21
HealthMate+ Machine Jr.
Austin Air National Sleep Foundation Bedroom Machine Filter
HealthMate Standard Machine
Austin Air HealthMate Standard Filter
Sentinel 539 Smoke & Odor Encapsulant with Antimicrobal Product Protection
Austin Air HealthMate Baby's Breath Machine
Austin Air Allergy Machine Jr. HEGA Filter
Share your knowledge of this product.
Be the first to write a review »
Back to top