Piranha NexStrip Pro contains a dual-action stripping
formula that begins by attacking the paint system on contact, then penetrates
into the paint system and delaminates it from underneath for complete paint
removal. The unique paste formulation clings to and tenaciously attacks
multiple layers of almost any coating system. Easy to work with and easy to
clean up, Piranha NexStrip Pro can be used on interior and exterior surfaces.
- Professional paint remover in a paste formulation that
clings to and attacks nearly any type of coating
- Does not contain dangerous chlorinated solvents, caustics
or methylene chloride
- This formula is low odor
-Recommended Use: To be used on interior and exterior surfaces
including concrete, brick, stone, aluminum, wood, fiberglass, plastic and other
Safety Data SheetHow to Use
Protect all surfaces not being stripped with polyethylene
sheeting. Protect plants and vegetation.
Piranha NexStrip Pro is a ready to use product. Do not
dilute. Mix before using for best results. Ideal working temperatures are
between 60-90°F; when applied at surface temperatures below 55°F performance
will be reduced and longer dwell times may be required. Higher temperatures can
dry out remover prematurely which will stop the paint removal process; reapply
to rewet the original coat if drying occurs prior to removal. Applying too thin
can result in premature drying and result in additional product applications.
Avoid direct sunlight. Workers must wear impervious gloves, apron and footwear
and safety goggles and/or face shield while using Piranha NexStrip Pro. Take
wind drift into consideration if spraying.
Before application, it is imperative to test on a small,
inconspicuous area to determine compatibility, required dwell time, coverage
and desired results. The end user shall determine suitability of the product
for its intended use(s), and the user assumes all risk and liability whatsoever
in connection with the application of this product. Note that the dwell time
required to remove a paint system is dependent on the application temperature,
humidity and the thickness/type of paint system being stripped. Will work in as
little as 2 hours. Typically, 8-12 hour dwell times will yield good results on
most coatings. However, extended dwell times of 24 to 72 hours can result in
more complete outcomes on multilayer paint systems. When Piranha NexStrip Pro
is to be left for an extended period of time (beyond 6 hours), cover with
Piranha Paper to slow the evaporation process and extend the product dwell
Apply Piranha NexStrip Pro with a brush, a trowel or airless
Brush: Synthetic, nylon or polyester bristle
Spray: .023 to .030 tip size, .75GPM flow rate, 3/8” hose,
remove filters to improve flow and clean equipment thoroughly after application
to prevent corrosion.
Clean all applicators and equipment with soap and water or
Apply Piranha NexStrip Pro between 1/16”1/4” thick. When
applying with an airless sprayer two coats will be necessary to achieve
required film thickness.
40-60 square feet per gallon. Coverage rates will vary
depending upon surface, application method and application thickness. Be
certain that all uneven or irregular surfaces receive adequate coverage.
Once the paint has fully softened and lifted, remove using a
scraper or putty knife. Collect all remover waste and paint residue for proper
disposal in accordance with all federal, state and local regulations. Do not
store or collect removed paint or residue in metal containers. Use plastic
containers only. Immediately following paint removal thoroughly clean substrate
with mild detergent solution. If there is a thin layer of paint residue that
remains agitation with a damp nylon bristle brush, sponge or pressure washing
will usually remove this layer. Perform a final clean water rinse and let
surface fully dry prior to painting. All Piranha NexStrip Pro residues must be
fully removed prior to painting. Close container after each use. Keep away from
heat sources and keep from freezing. Shelf life is 36 months in original,
closed containers stored at temperatures between 55 and 75°F.
Protective clothing should be worn. Wear rubber gloves. Wear
eye protection at all times. Face and head protection should be worn when
working at face level or overhead. Avoid contact with eyes, skin and clothing.
Avoid breathing vapors or mists. Do not take internally. Use only with adequate
ventilation. Wash with soap and water after each use. Keep container closed
when not in use. Store in a dry place at temperatures between 40°F (4.5°C) and